Hunter 28573 Manual de uso y cuidado descargar pdf

READ AND SAVE THESE INSTRUCTIONS

CFL Bulb (2)

WARNING: To reduce the possibility of electrical shock, be sure that the power is turned off at its source

(fuse or circuit breaker). All electrical components must be installed in accordance with national and local

electrical codes. To reduce the risk of ﬁre and electrical shock, the light ﬁxture should be used only with

UL, CUL, or ETL Certiﬁed Casablanca ceiling fans.

K2AA LIGHT FIXTURE

FOR USE WITH SELECT CASABLANCA GLASS BOWLS. FOR A COMPLETE LISTING

OF COMPATIABLE GLASS, ASK YOUR CASABLANCA DEALER.

Fig. 1

Fig. 4

Prepare Fan

1. Remove switch housing cap from switch housing

by unscrewing the two 8-32 screws. Fig. 1

2. Remove plastic wirenuts from switch housing

wires and strip

/2″ insulation from both wires

(black and white). Strip

/2″ insulation from both

wires of the light ﬁxture.

Install Light Fixture

3. Remove the center plug from the switch housing

cap and route the wires from the light kit through

the hole. Thread the cap onto the light ﬁxture

until cap is ﬂush with the light kit. Using the

provided washer and nut, secure the switch

housing cap to the light kit as shown. Fig. 2

4. Hold the light ﬁxture close to the switch housing.

Connect the wires from the fan and the wires from

the light ﬁxture together (BLACK to BLACK or

Blue to Black and WHITE to WHITE) by placing

the bare ends of the wires together and then

secure with the wirenuts. Fig. 3

Install Glass

1. For 3-Speed fans, remove the Fob from the

end of the pull chain and run chain through

holes in the bottom of the glass.

2. Insert the threaded rod of the light kit through

the center hole at the base of the glass.

Secure with the provided washer and nut

from the light kit, tighten by hand.

3. Insert threaded rod through center of glass

cap and secure with ﬁnial.

LIGHT KIT BASE

Inteli•Touch

Advan•Touch

GLASS

GLASS CAP

PULL

CHAIN

Glass for the K2AA is sold separately.

Refer to instructions that come with the glass

(if applicable) for additional instructions.

Note, provided with the glass are glass caps and ﬁnials

in several ﬁnishes to best complement your fan. There

are also two types of glass caps, one for 3-Speed fans

with holes provided for the pull chain, and a solid version

for Inteli•Touch and Advan•Touch fans.

FINIAL

LIGHT

FIXTURE

3-SPEED

WASHER

NUT

Dimensions:

Height Width

" 4

Weight:

Light Kit

1 lb

SWITCH HOUSING

SWITCH HOUSING CAP

8-32 SCREW

CENTER PLUG

Fig. 3

Fig. 2

Note: Bulbs included with this product will not dim. If this light kit is installed on a

fan with a light dimming function, then bulbs that are capable of dimming need to be

purchased separately.

NUT WASHER

IMPORTANT: Before discarding any packing material locate the following items:

WIRENUT (2)

5. Lift the light kit to the switch housing, aligning the screw holes, and secure with the two

8-32 screws from step 1.

Caution: Make sure wires are not pinched between the switch housing and cap.

Install Light Bulbs

1. Carefully thread the bulbs into the sockets. Tighten by hand. Fig. 3

P/N K2AA43001 RL0910

P/N K2AA43001 RL0910 1

Indice de contenidos

Pagina 1 - P/N K2AA43001 RL0910

READ AND SAVE THESE INSTRUCTIONSCFL Bulb (2)WARNING: To reduce the possibility of electrical shock, be sure that the power is turned off at its source

Comentarios a estos manuales

Sin comentarios

Hunter 28573 Manual de uso y cuidado

Busca en linea o descarga Manual de uso y cuidado para No Hunter 28573. Hunter 28573 Use and Care Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para No Hunter 28573